Chip Directory Host site

Advertisement provided by Adprov

ABC of electronics terms

Click on the first letter of the electronic term you're looking for:
0..9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

(To find chips for distinct functions, see the functional pages.)

O

Obsolete chip

A chip that isn't produced anymore

local More information

OEM

Original Equipment Manufacturer

www.electronics-oems.com/companies.html list of electronics OEM's

See also CEM.

One-wire bus

One wire bus protocol by Dallas.

See 1-wire.

Operating System

This section became to big, so see local.

Open-collector output

Early TTL* chips used to have an internal transistor at their output that could either provide 0V or it would have a high impedance. To use it for normal digital logic purposes an external transistor was needed to pull up the output voltage to 5V (nomally). To calculate which value the resistor has to have consider that when the output is pulled low by the chip, the resistor will be a short from the 0V output to 5V. Therefore the resistor value needs to be as high as possible. In the other case the resistor value must be low enough to provide 5V through it to the input of the circuitry that is connected to the output of the chip. You'll need to know what the internal resistance of this circuitry is or what amount current it draws. You can also determine the value of the resistor experimentally. Start with a very high value like 1M or 100K and divide the value by 10 until the resistor manages to pull up the voltage at the output of the chip to well enough over 2.7 V (for traditional TTL*). Beware: In some applications you will also need to consider the rise time of the signal. Instead of pull-up, pull-down is also used sometimes, but it's much less common.

The open-collector system has still very valid uses, because you can connect a lot of open-collector outputs together and they'll form a natural inverted OR* port. If one or more of the ports is low the resulting signal will be low. Or put otherwise, only when all the outputs are 'high' (=high impedance) the resulting signal will be high. This OR* port mechanism has two very useful applications: For connecting a lot of interrupt signals together, because often new devices are connected to a computer system over time and the second usage is when connecting a lot of systems over a bus where often also devices are added at a later stage and the devices have to be able to talk in turn bidirectionally over a signal line. The line can also be used to determine which device is allowed to take over the bus next. At a certain stage of the protocol they will all send their own ID in binary over the line starting with the most important bit and as soon as a device notices that at a moment that he was sending a 1 but the line was 0, and thus pulled down by another device it will stop competing. This way at the end only one device is left (when all devices have unique numbers) and it may take the bus. Once it's ready the other devices will compete all over again and the device with the next lowest number will win etc.
Philips' I2C* bus uses an open collector bus.
By the way, many modern micro* controllers have output pins that can also be set to work as inputs. When they are used as inputs they are high-impedance making them effectively tri-state ports. It's now very easy to implement an open collector bus, since you just switch between 0V output and input to get the two desired states. And during 'high' you can measure if the line was pulled down by another device... Don't forget to add a resistor as a pull-up to the system! ;-) Ah and if you want to be able to detect a shortage on the line, you'll also need to be able to check if high is really high. With most micro* controllers you'll need to use an extra input because you can't read the port as input when you're using it as output. :-( It's very easy to make mistakes with these kinds of ports when you're using bit or-ing and and-ing (or the controller does this itself when you're using bit set and reset instructions) because when reading back the port you'll usually don't get the previous state of the output ports but the inputs... It would have been much better when the chip designers had used different bytes for the data of the ports for the input and the output functions of the port.



Open Source Hardware

Besides 'open source software' there are also project groups working on 'open source hardware'.

www.angelfire.com/wa2/ratgod/odcp/ The Open Design Computer Project - site is still under construction in 200107

Operational Amplifier

Often abbreviated to OpAmp*.

Books:
title order at Amazon USA price indication
IC* Op-Amp Cookbook ISBN: 0672224534 $25
Joe Carr's Op Amp* and Linear IC* Handbook ISBN: 1878707205 $30
Simplified Design of IC* Amplifiers (The EDN Series for Design Engineers) ISBN: 0750695080 $30

www.chipdir.nl/amazon/chipdir.php?mode=books&searchtype=KeywordSearch&search='op+amp*'
www.chipdir.nl/amazon/chipdir.php?mode=books&searchtype=KeywordSearch&search=amplifier

Optics

See next item.

Optoelectronics

Links:
nyquist.ee.ualberta.ca/pub/cookbook/optic/ In the Circuit Cookbook
local Fiber optics

See:
local Companies


Date:    19971124
From:    Frank Fremerey
To:      Jaap van Ganswijk
Subject: Electronic Optic Chip breakthrough report
Dear Jaap,

I finally found my note on the above subject. It reads:

"Raphael Tsu, an electrical engineering professor and Qi Zhang, a postdoctoral fellow, say they've successfully linked electronic and optical technology on the same silicon chip"

Both live and work at the University of North Carolina at Charlotte (UNCC) and say, their discovery could make chips 100.000 times faster. They further say, that a lot of unsuccessful experiments tried this before, but they have now made it. The money comes from the Naval Research and Army Research Office.

The thing was reported by GMSV on 19970916 (www.sjmercury.com) and further reading is to be found in SCIENCE-magazine and I will cover the findings in my article.

Regards,
Frank

Organ

www.systemsinfo.com/ Chips etc. for organs and electronic keyboards

www.chipdir.nl/amazon/chipdir.php?mode=books&searchtype=KeywordSearch&search=organ

OS

See Operating System

www.chipdir.nl/amazon/chipdir.php?mode=books&searchtype=KeywordSearch&search=os

Overclocking

Making a MPU or MCU run faster than intended by the manufacturer.

www.kryotech.com/ The upcoming AMD Athlon SocketA Thunderbird processor with performance enhancing cache memory, cooled to a chilly -40°C will give you the high performance processing power you could only imagine until now.

Overdrive(R) Processors

Faster processors from Intel to replace older slower ones.

www.intel.com/pressroom/archive/releases/DP080497.HTM
www.intel.com/pressroom/


Click on the first letter of the electronic term you're looking for:
0..9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

  Search Tips
  Search Tips

Ad for PCI video capturing boards by Dektec.
Goto: Main Mirror About Author
Register: Yourself Company
Feedback: Correction Addition Question Forum
Order: Chips (Deutsch) Chips (English) Chips (Nederlands)

Advertisement by Adprov

Viewable with any browser